Bay Heating & Air Conditioning has been servicing the heating and air conditioning needs of Bay Village OH since 1944.
Air Conditioning Repairs & Air Conditioner Replacements, Heating Repairs & Furnace Replacements and much more!
Call us now at: 440-249-0500 or check out the reviews and testimonials from your neighbors, that make us the top rated service provider in Bay Village OH.
for Bay Village, OH
Our Reviews by City
Work done was exactly what we wanted
RWGardner - Bay Village, OH
The team showed up on time, did the correct work, and were very neat!
Steve - Bay Village, OH
Great service .
DrewMary - Bay Village, OH
Dubin - Bay Village, OH
Good Service, Good Advice
Brian - Bay Village, OH
Long Time Client
Rob - Bay Village, OH
Very disappointed that I am being charged for a third time in as many months for the same issue. I’ve had a service contract for over a decade and when it was time to replace my air conditioner I didn’t call anyone else even for an estimate; I automatically went with Bay Heating & Air Conditioning. This experience gives me pause to consider that loyalty.
Gary - Bay Village, OH
Bill - Bay Village, OH
McCracken - Bay Village, OH
Gary - Bay Village, OH
On Saturday morning my furnace stopped working and a message was on the controller screen "System Malfunction, call Technician". I called and Brian Miller was sent out. He identified the cause and determined a major repair was required that could not be done until next week. He was able to get the furnace running well enough to keep the house reasonably warm until the repair can be performed.
Diesing - Bay Village, OH
Jose is very competent and knowledgeable.
Philip - Bay Village, OH
considering the weather
Schrantz - Bay Village, OH
this past weekends weather, blizzard, Bay Furnace & Marty Taylor rose to the occasion and got us the heat we need in a very professional manner ...JIM Schrantz
Great, Quick service
Croyle - Bay Village, OH
Talbott - Bay Village, OH
Appreciate Marty’s Expertise
Bypass infinity control with regular thermostat to get heat until tomorrow
Equipment is confirmed same on file. Found end switch on damper not made. Cycle damper, boiler fired. Cycle boiler to check, ok.
Furnace tuneup. Burner and blower compartments were inspected. All safeties and connections were checked. Vent pipe was sealed with high temperature silicone. Unit was cleaned and tuned up. The system is in proper working order at this time.
Replace Part. Replace 2-Stage 80% Circuit Board, Cycled Hi And Lo Stage Fine At Fine At This Time.
Unit Not Working. Found A Bad 2-Stage 80% Inducer Assembly Not Working. Went to the shop picked up two space heaters and left them here .
Hot Smell. (Crawlspace) Found A Bad Drain Pump & 2=Plug Air Filter, Replace Drain Pump And #16x20x1 & #16x25x1 Air Filter, Cycled Unit Fine At This Time,
No Heat. Replace Flame Sensor Reading 1.5 M.A. Clean And Tests Reading 4.5 M.A. Cycled Unit Fine At This Time
Replace Parts. Found A Bad 3-Stage Gas Valve. Replace 3-Stage Inducer Assembly And 3-Stage Gas Valve, Set Gas Pressure Cycled Unit All 3-Stage Fine At This Time.
Found upstairs radiator bracket bent sideways radiator not pitched correctly repair bracket alignment and bleed the radiator cycle to check OK. On fall tuneup need to bring boiler pressure temperature gage as current gauge not reading pressure correctly 1/4 inch diameter x 3 inch long.
Upon arrival I found the pilot light out. Changed thermocouple. Lit pilot. Cycled system and system is operating properly at this time. Thanks Brian.
No Heat. Found A Bad Inducer Board Replace Inducer Board Works, More more failures or occur with the furnace .
Warranty furnace replacement
No Heat. Found A Bad 3-Stage 90% Inducer Assembly. Order Part Will Follow Up And Replace.
Unit Making Noise. Found The Bearing Making Noise On A 80% Inducer Assembly, Replace Cycled Unit Fine At This Time.
Replace water panel also performed furnace tuneup clear condensate trap clean flame sensor vestibule burners and controls fire furnace to check OK
Checked furnace operation OK customer turning thermostat to 65 and then back up to 73 to 75 which is quite drastic suggest only going maximum of 5Â° at setback because energy saved during setback is consumed getting temperature back up to desired setting when occupied found no problems with heating system.
Found furnace reading code 42 which is not on status codes of furnace looked in infinity control and 42 is indicating inducer fault inducer did start in test mode ramped up then shut down still flashing code 42 turn off system turned fan to low instruct customer not to put space heaters on same circuit which was what tripped circuit breaker when she tried this morning
Found system with adjustments made to bypass first stage heating. Also fan jumped up from low to med hi. System is oversized for home. My strongest recommendation is to replace entire system for proper operation. To add humidifier new plenum would have to be fabricated.
No Heat. Found A Bad 2-Wire Pilot And Analog T-Stat, Replace 2-Wire Pilot And Non Programmable Thermostat, Cycled Unit Fine At This Time.
Nono heat. I found the thermostat hanging on the wall. One wire had broken off for communications. I remounted thermostat to the wall , reattached the wires and cycled the furnace with proper operation.
No heat. Upon arrival I found the furnace locked out on limit tripped. I reset the furnace and it fired I found the reason was a blocked filter. The customer has a filter somewhere and says they will replace it.
Found 3 amp fuse blown. Check for shorts, none. Replace fuse and filters in both rooftop units, cycle to check, ok.