Bay Heating & Air Conditioning has been servicing the heating and air conditioning needs of Avon Lake OH since 1944.
Call us now at: 440-249-0500 or check out the reviews and testimonials from your neighbors, that make us the top rated service provider in Avon Lake OH.
for Avon Lake, OH
Our Reviews by City
New Furnace in January
AndersonDoug - Avon Lake, OH
Thank you for all the support! From multiple options to replace old furnace, fitting into a expedited schedule, installation, to walkthrough of wireless thermostat. Great job Bay Furnace!
HitchcockThomas - Avon Lake, OH
Very good service
Hardy - Avon Lake, OH
Kept me informed
great service Jason really knows what he is doing.
Martin - Avon Lake, OH
jason is great at customer service. and is a skilled furnace diagnostician.
Wonderful Response and Professional Service
DeGreen - Avon Lake, OH
Great service. Jose is the best. Pay him well.
Dannemiller - Avon Lake, OH
Wonderful experience. On time. Very knowledgeable. Efficient!
Air Conditioner Drain
Lawson - Avon Lake, OH
Jason was great. The price was little high for the procedure.
Villari - Avon Lake, OH
Buck - Avon Lake, OH
Alaa - Avon Lake, OH
Hardy - Avon Lake, OH
Very through with the work. Quality
Novess - Avon Lake, OH
Jose did a wonderful job as always
Arlene Keehan - Avon Lake, OH
Good service, on time and well done.
Alexander - Avon Lake, OH
Jason was on time and very polite. What a great company.
Great service at a good price
Ritchie - Avon Lake, OH
Coustomer noticed error codes. Upon arrival there were no error codes present. Coustomer noted error code 13 & 12. I cycled the furnace in first and second stage with no faults or failures. I inspected the filter. The furnace is in proper working order at this time.
Checked thermostat settings spoke with Jim Price assured humidifier with fan was turned off also need to get on carriers portal and check duct assessment start hour as this may be whatâ€™s turning fan on will need to be changed to sometime less inconvenient for customer.
Went to home to figure out why furnace was running but thermostat was set at 56*.
Clean burners, flame sensor, vestibule and controls. Check blower, motor and filter check all operating and safety controls. Check humidifier water panel and operation. Fire furnace to check ok.
Club Furnace Tuneup. T-Stat, 78 Ohms HSI, Flame Sensor, 2-Stage 80 Inducer, Electrical, 1.6â€ 3.5â€ W.C. Gas Valve, Burner, #16x25x1 Air Filter, 10+370 Run Cap Blower Motor, 50* Outside, Cycled Unit Clean And Check.
$119.95 Furnace Tuneup. T-Stat, 78 Ohms, Flame Sensor, 80% Inducer, 3.5â€ W.C. Gas Valve, 14x25x1 Air Filter, 7.5+370 Run Cap Blower Motor, 53* Outside, Cycled Unit Clean And Check.
Heating tune up. Adjusted upstairs damper for comfort. If unit overheats it needs to be opened.
Found furnace going off on limit in high stage check filter blower and motor increase fan speed to medium high cycle furnace several times with no failures
Club Furnace And Humidifier Tuneup. Replace #10Wp. â€œFurnaceâ€ T-Stat, 53 Ohms HSI, Flame Sensor, 90% Inducer, Electrical, 3.5â€ W.C. Gas Valve, Burner, Drain Trap, #14x20x1 Air Filter, 7.5+370 Run Cap Blower Motor, 34* Outside, â€œHumidifierâ€ Hum-Stat, Bypass Damper Open, Drip Tray, Feed Tube, Water Valve, Electrical, Drainline, Cycled Unit Clean And Check,
Flushed Condensate trap. Cleaned flame sensor. Checked ignitor. Checked venting. Cycled system operating properly at this time.
Heating tune up
Furnace tune up. Checked all readings. Inducer and blower, ok. Temp rise good. Replaced water panel. Replaced filter, customer supplied. Cleaned flame sensor. Igniter checked ok. Vacuumed cabinets. Customer has no CO detector in home. She is getting one from Home Depot .
Clean burners flame sensor vestibule and controls checked blower motor and filter check all operating and safety controls fire furnace to check OK check humidifier water panel and operation water panel and filter recently replaced by customers unit operating well found no problems
Cleaned condensate drain. Cleaned flame sensor. Ohmed out hot surface igniter. Vacuumed and cleaned entire furnace. System operating properly at this time
I found the furnace was not making any noises for me at this time. I cycled both units and they are operating properly at this time. I inspected the blower wheel for signs of failure and found none. I hand spun the blower wheel and it is not moving as freely as I would like. Due to age I would recommend replacement of the furnace.
Tuneup complete. Air filter was replaced by customer. Inspected and cleaned hsi, flame sensor, intake, trap, burners, inducer, blower, safeties, controls and cabinet. All electrical connections are secure. Ran furnace in heat test mode from tstat with proper operation at this time. Reset tsat. Cycled humidifier. Customer replaced their own water panel. Found humidifier to be leaking. Reposition tray and adjusted water flow. Set infinity stat back to the way it was found.
Heating tune up. I replaced the filter with the coustomers suply.
Replace Part. Replace 90% Inducer Assembly, Cycled Unit Fine At This Time.
Water leak. I found the connection from the secondary heat exchanger to the trap is leaking condensate. The filter is dirty. I would recommend replacement of the trap and hoses.
Club Furnace And Humidifier Tuneup. â€œFurnaceâ€ 54 Ohms HSI, Flame Sensor, 90% Inducer Making Noise Recommed Replace, Electrical, 3.5â€ W.C. Gas Valve, Burner, Drain Trap, 40+370 Run Cap Blower Motor, 36* Outside, Cycled Unit Clean And Check. â€œHumidifier Fan Powerâ€ Not Used.
Installation of 2 humidifiers
I replaced and set up infinity control.